NEW 3d Systems ProJet printhead service

Discussion in 'Rapid-Prototyping' started by DMC, May 12, 2015.

  1. DMC

    DMC Scott Hudson

    I have around Forty NEW 3d Systems Revision B print heads. :stig:

    $3000 if you are able to send me your assembly.

    $3000+ travel cost + $500 for a tech to fly to location and change.

    So far, we have changed many.

    Also, we have about any other part you could possible need.

    Power Supplies, Control Boards, cables, etc.

    Scotty 1-804-285-0777
     
    Projetter likes this.
  2. Dejvis

    Dejvis Member

    Hello DMC,

    How much would xenon bulb for 3510 mp model cost?
    Original part number: 23022-902-00
     
  3. DMC

    DMC Scott Hudson

    $1000 new
    $500 used

    804-285-0777

    Usually they last forever. Only if glass breaks does it need replacement.
    They are VERY fragile! I prefer to send entire Xenon hood assembly.
    The big aluminum cover and everthing in One piece.
     
  4. Dejvis

    Dejvis Member

    How much would xenon bulb with entire Xenon hood assembly cost?
    Also, do you have a UV sensor? If yes, how much would that cost?
     
  5. DMC

    DMC Scott Hudson

    Forget that stupid sensor.
    We lower minimum power for that sensor to almost nothing on all printer.

    Either Xenon works, or it does not and is broke. Yes or No.

    Yes, sensor get dirty and detect less and less power over time, but in reality the power is the same.
     
  6. DMC

    DMC Scott Hudson

    Go to parameters, curing, lower setting of minimum power to under 100.
     
  7. Dejvis

    Dejvis Member

    Xenon not working bulb is broken.
    How much would xenon bulb with entire Xenon hood assembly cost?
     
  8. DMC

    DMC Scott Hudson

    $800 for entire assembly.
    Plus a little for shipping please to Litho...
    6 month warranty!

    Or, $1000 for new bulb.
     
  9. Minimoke

    Minimoke New Member

    I have a Xenon with blackened glass on one side (inside)
    The glass is clean.
    prints are not accurate anymore. Seems like it is not hardened fast enough, although all flash cycles are checked.
    Light value from lamp is about 1100 - 1300.
    Final result is hardened.
    Any ideas?
    20160314_125132.jpg 20160314_125141.jpg
     
  10. DMC

    DMC Scott Hudson

    I have many of those. You need One?
    I am very impressed you removed it without breaking it!

    Lamps come from Perkin Elmer.
    To get a good deal, you need to buy 5-10 pieces.

    But, of course 10 cheaper than buying from 3ds!!
     
  11. DMC

    DMC Scott Hudson

  12. Minimoke

    Minimoke New Member

  13. DMC

    DMC Scott Hudson

    One supplier is www.tjslasers.com

    part number TJS-1938-0

    I am happy to sell to you for less. :)

    Can ship today.
     
  14. Strick9

    Strick9 New Member

    Do you have any conf. A boards? We are still trying to get our printer fixed. Our repair guys can not find a conf. A board. They tried a conf. B but it wouldn't control the vacuum. 3D Systems doesn't make any more and has none in stock. At wits end. Our printer has been down since September. Please help. I have guys to install but no part.
     
  15. DMC

    DMC Scott Hudson

    If I could find Ten Rev. A printheads, then I would have them all sold in One second.

    You need around $10,000 in parts to upgrade to Rev. B

    Main Control Board
    Main Backplane board,
    Lots of other circuit boards, cables, mounting brackts, etc...

    Then, the actual printhead itself.
     
  16. DMC

    DMC Scott Hudson

    OK, I have maybe Six Revision A printheads fully tested and ready to go.

    Maybe a few more, but we have not tested yet.

    I actually have a pile of over Twelve of them, and just bought Two more.

    These are like finding a unicorn. I search every day for them for many years now.

    I am happy to sell you One for $3500

    Send me your entire printhead assembly, or we come there and install?

    804-285-0777

    Scotty or Don or Luciano
     
  17. Strick9

    Strick9 New Member

    I need the communication board and motherboard for a config A. The main control of the computer is down. We got one but the port on communication board was bad.
     
  18. DMC

    DMC Scott Hudson

    Hmmmm.

    I think better to call me.
    I do not know what you are calling a communication board?
    I doubt you need a motherboard also.
    Maybe just an HDD? or the ribbon cable that is for the serial port com?
    I bet you just have something screwed up in the software or something else man.
     
  19. DMC

    DMC Scott Hudson

    I know all about it. You get, "Serial Motion Interface Com port error" eh?
     
  20. Minimoke

    Minimoke New Member

    Hi DMC,
    I received the new lamp and combo in great order, within 36 hours.
    Thanx for your help, great service.
    (btw, roller problem is solved, will not need new one)
     
    DMC likes this.

Share This Page