Wich scanner with Exocad choose?

Discussion in '3D Scanners' started by Ildent, Jul 26, 2018.

  1. Ildent

    Ildent New Member

    Hello everyone, i want to change my old 3shape D250 Scanner with Exocad scanner im interested to read youre recomendations.

    Thank you.

    (and sorry for my bad english)
     
  2. 2thm8kr

    2thm8kr ɹotɐɹʇsıuıɯqA Staff Member

    You are switching from 3Shape to exocad?
     
  3. Ildent

    Ildent New Member

    Yes, i want to switch because its really closed system and expenssive.
     
    French Cadman likes this.
  4. Kvonn3gut

    Kvonn3gut Administrator Staff Member

    Several scanners work great with exocad. Medit, DOF, and Shining 3d are all competitive scanners. Price is the only big difference between the three companies. I would recommend you do some research and take a look at all 3 brands. We have used all of those scanners with success over the years.
     
    Ildent, DMC, cadfan and 1 other person like this.
  5. EJADA

    EJADA Well-Known Member

    DOF HD. I have two fantastic!!!
     
    DMC and 2thm8kr like this.
  6. DMC

    DMC Scott Hudson

    If you need cheap solution then shining3d ds-ex and exocad for 8000usd from me.
     
    cadfan likes this.
  7. Giacomo

    Giacomo New Member

    Salve a tutti,
    anche io avrei bisogno di un consiglio.
    quale scanner scegliereste tra medit t300 / t500, Dof Freedom o swing ???
    che secondo voi il migliore ???
    Grazie
    Hello everyone,
    I would need advice too.
    Which scanner would you choose between medit t300 / t500, Dof Freedom or swing ???
    which according to you the best ???
    thank you
     
  8. 2thm8kr

    2thm8kr ɹotɐɹʇsıuıɯqA Staff Member

    I like the DOF Freedom HD. No model holder to fight with.
     
    EJADA likes this.
  9. Giacomo

    Giacomo New Member

    dicono che il meditabondo T500 è più velo e preciso.
    12 secondi e 7 micron.
     
  10. cadfan

    cadfan Moderator Staff Member

    for which propose T 500 is not better than 300 which 7 micron you know what it means ??
     
  11. Giacomo

    Giacomo New Member

    I'm not an expert.
    would you mind enlightening me ???
    thank you
     
  12. cadfan

    cadfan Moderator Staff Member

    this part is done with the 7 my nothing impressive not sure if any dental scanner cant.

    12836  7 micron.png
     
  13. Ildent

    Ildent New Member

    New
    I need a scanner wich have receeler and can buy from Spain, and to have got a technical service here if

    I need if to make cemented crowns, implant crowns and bridges and implant bars ? For wich i have to choose or will be better for the use ?
    Thank you!
     
  14. bigbrush

    bigbrush Well-Known Member

    Hello,
    if I were you, I would ask my colleagues about their experiences with the dealers. How was the support in case of problems, how long did it take to get notified and how long until the problem was solved.
    Then I would make an offer to these dealers and decide.
    What good is the Ifo which is the best scanner if you can not get support?
     
    2thm8kr likes this.
  15. try UP300 dental 3d scanner, very fast speed ( 8 sec for bite, 20 sec for arch, 28 sec for 12 units multi-dies and 90 sec for impression) and high accuracy 10 micron.
     
  16. Justin Yoo

    Justin Yoo New Member

    I think that Freedom HD of DOF is Good!!

    You don't need model holder anymore, Just put the models in scanner.
     
    EJADA and 2thm8kr like this.
  17. dougola

    dougola Well-Known Member

    I have an opportunity to purchase a DOF scanner. I don't have all the particulars about it yet, but it was initially sold by B&D in Utah. Anyone know if they had any closed system setup on the stuff they sold? Also, what else should I be on the lookout for? There is also Exocad software that will need to be transferred. The question here is, of course, if it hasn't been updated in a couple of years will I need to pay for the past updates if I buy, or will Exocad let the transfer happen and only pay for current update?
     
  18. 2thm8kr

    2thm8kr ɹotɐɹʇsıuıɯqA Staff Member

    AFAIK, you can't transfer the dongle to a new reseller without updating the dongle to a current contract and maybe a minimal transfer fee for the new reseller.

    Depending on what you want to or need to do with that exocad dongle, maybe it doesn't need to be updated.

    What model scanner is the DOF?

    @Kvonn3gut care to share some words of wisdom here.
     
  19. dougola

    dougola Well-Known Member

    I'm not sure yet. I have a friend who has nothing but 3Shape stuff. He bought a lab and put the guys digital equipment in a corner. He's going to get with me later this week to give me the info and what kind of $$ he would like for it. I'll post everything here so I can get the proper feedback. I don't want to buy something that is not supported anymore.
     
  20. EJADA

    EJADA Well-Known Member

    Just curious which DOC scanner?? Do you know??
     

Share This Page